Belgian (Almost) Red Ale

Belgian Red Ale Recipe

I can’t call this a Belgian Red Ale, because it’s not a sour beer. It’s just a tasty beer with a red hue that puts a delicious yeast to good use. Hops are kept in check, but the strength of the beer will warm your heart on a cold winter’s day.

Recipe Profile

  • Method: 1 gallon BIAB (Brew-in-a-bag), single stage
  • Target OG (Original Gravity): 1.071
  • Target FG (Final Gravity): 1.016
  • Bitterness (IBUs): 26
  • Estimated ABV: 7.2%
  • Boil: 60 minutes


  • 2.25 lbs Maris Otter Pale Malt
  • 4 oz Caramunich Malt
  • 2 oz Aromatic Malt
  • 1 oz Chocolate Malt
  • 0.25 oz Saaz Hops at 60 minutes
  • 0.25 oz Saaz Hops at 15 minutes
  • Belgian Abbey II Yeast (Wyeast 1762)

The Mash

  1. Bring 9 litres of water to a temperature of 163°F. Add your grains and give everything a good stir until the whole thing looks a bit like oatmeal. Shut off the heat, cover with a lid, and let it steep at 156°F for 60 minutes.
  2. Then you need to “mash out.” You put the heat back on, and raise the temperature  to 168°F (75.6°C) and keep stirring for 7 minutes.
  3. Remove the grains and prepare for the boil. If you’re using a bag, just pull it out and let it drip near-dry above the pot. If you’re using a colander, strain to remove the grains, preserving the wort, which you’ll add back to the pot.
  4. Check that your gravity is on track and correct it, if needed. You need 92 gravity points for this recipe, and our target post-boil volume is 1.3 gallons.

The Boil

  1. Start the boil by bringing your wort up to a boil. Once boiling, start your timer. Add your bittering hops, as prescribed above.
  2. Meanwhile, prepare your sanitizer solution.
  3. Just before the boil is complete, make an ice batch in your kitchen sink. Load it up with as much ice and cold water as you can. Once the boil is over, transfer your pot to the sink to cool your wort to pitching temperature, as prescribed on the yeast pack. Remember to sanitize your thermometer every time you check the temperature.
  4. Meanwhile, thoroughly clean and sanitize your carboy, screw cap, airlock, funnel, and strainer/colander. You want everything to be ready to go once the wort is at the right temperature.
  5. Once the wort is at pitching temperature, transfer it to the carboy by passing it through a strainer overtop the funnel. Do not fill the carboy higher than the one gallon mark.
  6. Aerate the wort.  Cover the fermenter with a screw cap and gently rock the carboy back and forth for a few minutes to mix in some air.
  7. Pitch the yeast! Use sanitized scissors to cut open the package and pour in only half of the yeast.
  8. Seal the carboy by filling the airlock with sanitizer. Fit it in the screw cap. Move the carboy to a dark spot, free of the home’s daily commotion for at least 14 days (but ideally not more than 21).

Bottling Day

  1. Move the carboy to a the countertop, if it wasn’t already there. If the wort got lots of movement during transfer, let it sit so that any stirred-up yeast has a chance to re-settle.
  2. Sanitize everything that will come in contact with the beer: bottling bucket, auto-siphon, tubing, filler, bottles, and bottle caps.
  3. Dissolve 0.59 oz (17g) corn sugar in enough boiling water to dissolve it. Add the dissolved sugar solution to your sanitized bottling bucket.
  4. Fill your auto-siphon and hose with sanitizer before submerging in the carboy. Transfer the solution to a spare container until the beer has completely replaced all the sanitizer in the tubes. Now you can place the end with the bottle filler in the bottling bucket, which should also be on the floor and gently transfer the beer from the carboy to the bucket.
  5. Transfer all the liquid up and the point where it reaches the sediment. Leave the sediment in the carboy.
  6. Now, move the bottling bucket to the counter and siphon the beer quietly into each bottle. When the liquid gets to the very top of the bottle, remove the bottle filler, which will leave the perfect amount of headspace at the top of the bottle.
  7. Cover each bottle with the sanitized caps and cap them into place, or secure your sanitized swing-top caps if using those.
  8. Store the bottles upright in a quiet, dark corner at 65F (18.5C) or so.
  9. Wait 30 days, if you can. If you’re way too curious (I can’t blame you!) try and hold out for 14 days. If you absolutely can’t wait, you can try after 7 days, but the beer really needs at least 14 days to condition.


3 responses to “Belgian (Almost) Red Ale”

  1. Andrew Boulton

    Thanks for the recipe, I’m hoping to scale this up to a 5 Gallon batch and have a few questions regarding the boil and hop additions.

    1. Should the boil last 60 minutes?
    2. Are the times given on the hop additions the time to ‘flame out’ (i.e. 60 and 15 minutes before stopping the boil)?

    Thanks again.

    1. Hi Andrew,

      Yes, it’s a 60 minute boil, and the times are to flame out, so 60 minutes would be at the beginning of the boil, etc.

      Good luck!

  2. Jonny

    Hi, I would like to use this recipe but on a larger scale.
    like 4x how much water should i start with? the other ingredients will simply be 4x? boil times?
    thank you

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.